Car Key Button Repair 11 Thing Youre Not Doing

Car Key Button Repair
A broken car key can be frustrating. It is possible to contact an emergency locksmith service 24 hours a day to assistance or purchase a replacement remote.
However, you might be saving money by fixing an old key fob instead of replacing it. This is especially true if the problem is caused by an old switch or a damaged contact.
repair car key
If the buttons on your key fob are not responding to your pressing them, this could be a sign the battery has failed or is nearing its end of life. It's simple to replace the battery yourself, rather than paying for an auto locksmith or dealership.
First look for the battery compartment. The battery compartment is usually located on the back of the key fob, and can be hidden behind a cover that opens or a button that opens the access point. When the compartment is exposed, look for the small button-cell battery. This is typically shaped like an oblong coin and is has a plus and minus sign. Remove the battery that is old, and replace it with a new one. Make sure that the plus and minus symbols are aligned correctly.
Once the battery is installed close the compartment and snap the two parts of the key fob together. Before closing the door make sure to align and snap the components in the correct position. Press any of the buttons to verify that they work properly.
If your remote keyfob does not work after replacing the battery, it could be other issues that require a different type of repair. Dropping the fob into a puddle can cause it to cease functioning. Alternatively, it might be suffering from an electrical issue within the device or might need to be deprogrammed by a dealer or locksmith. Try to figure out what's wrong related to your key fob using these other common car troubleshooting techniques.
Switches
Depending on the year and the manufacturer, there are various kinds of switches available on the car keyfob. The older model of key often has an additional chip that is visible in the case, whereas the newer keys are more advanced and work by sending signals to the car. The buttons on a key may be damaged or worn out through normal use, regardless of the model. As a result, they become difficult to press or even unresponsive. If you attempt to press the button too hard the button, it could cause damage and may even stop the key from starting your vehicle in the future.
If you are unable to get your key to function, try changing the batteries. If this doesn't work, then you may have to clean the key fob or adjust its switches. These tiny electronic switches are more prone than larger parts of the key to break because they are constantly tossed about.
The switches are rubber-like, and are coated with an electric conductor film that is prone to wear out over time. Fortunately, they are also tiny and affordable to replace. They are soldered onto the circuit board, therefore you need to carefully take them off without causing any damage to anything else. You can then solder the new ones into and reassemble the fob.
Do not use your car key fob for more than a couple of hours at a stretch and do not leave it open. Also, make sure you find a secure place to keep your key in when you're not using it.
If you've already tried cleaning your key fob or replacing the battery, but the issue persists it's probably time to think about hiring an appointment with a locksmith. A professional locksmith can test the frequency of your key to determine if it's still able to communicate with your vehicle. They can also open and replace micro switches, alter cases and more.
Outer Case
If the buttons can't move freely up and down the case, they could become stuck or break. If cleaning the case using rubbing alcohol and a cotton swab does not work, it may be necessary to take off the case. If the contacts that the buttons touch aren't suitable for the application, or if they are worn, changing them might be the only option.
Certain keys have buttons made of rubber, which wear away over time. The rubber stretches and nails pierce it and the buttons can become difficult to press. In this situation, the key may fail and it's time replace the case or buttons. This repair involves disassembling your remote, looking for the switch on the board, then heating the solder, and then carefully taking them off. New buttons are then soldered to the circuit board. The case is then rebuilt with the horse shoe key blade piece is attached. The new buttons should be snugly fitted into the case in order to prevent them falling out.
Inner Case
Over time the buttons on your key fob can be damaged or stuck as a result of the constant jostling and accidental pressing. Utilizing metallic tape and a hole-punch, you can often quickly solve this issue in the event your car is away from home when the key fob doesn't work, allowing you to unlock the doors, but not start the engine. This quick fix could allow you to safely make it back to your car and complete your journey.